Stainless steel mugs and tumblers are increasing in popularity, and there’s a reason. These bad boys, manufactured by companies such as YETI, RTIC, and Silverback are said to be indestructible and can keep your tasty beverages colder and hotter longer than any other tumbler on the market.
With consumer’s desires for personalized products, there is no doubt that laser engraved YETI and other stainless steel mugs are a hot commodity and something you should definitely be offering if you have a laser engraving machine.
In this video, we show you how to laser engrave a stainless steel mug with an AP Lazer stainless steel laser engraving machine.
How to Laser Engrave a Stainless Steel Tumbler Mug
You will need:
- Stainless steel mug of your choice
- CerMark metal marking spray (we used a sprayer and diluted it with denatured alcohol)
- Rotary tool attachment
- An AP Lazer Mug Engraving Machine
1. Measure tumbler mug and prepare artwork for laser engraving. Tip: You will need to rotate your file 90 degrees to correspond to the positioning of the Rotary Device.
2. Set up the rotary device. Unplug the y-axis and plug in the Rotary Device plug. See video on this here.
3. Apply a thin, even coat of CerMark Metal Marking Solution to the clean surface of the stainless steel mug. Let dry for 2-5 minutes.
4. On a 100w AP Lazer, run your file at 15 Speed, 80 Power, and .0025 Scan Gap. Engrave with the 2″ lens. Experiment with different speed and power settings if needed.
5. Once engraving is complete, rinse off excess CerMark. Enjoy your personalized stainless steel tumbler!
Personalized Tumbler Retail Values
Price points for engraving YETI cups and other stainless steel cups range anywhere from $5 to $40 based on location. Customers using AP Lazer have said: “I’m making $40 a cup. For bulk orders, I’m getting $15-$20 here in California“. “I get 25 per cup all the time“.
“CerMark is not cheap…here I get $25 a cup and $30 pending”, and “Depends on where you’re located. I can’t get more than $15-20 per cup on single cups. The distributor I work with on large orders only pays $6-10. You can run a lot more per hour when it’s the same logo over and over.”
Tips for Engraving from AP Lazer Owners
- Weigh the cup down with a wet dishrag to prevent slipping on the wheels of the rotary device.
- Test on stainless steel material from Walmart to save money while testing.
- Make sure the layer of CerMark is thin and even. A thick, uneven layer will not produce good results.
- Stick to your price if you feel the price is right. Never let customers dictate the price.
- Mask where your cup makes contact with the drive wheels on the Rotary Device to eliminate overspray getting on them. (Can cause slipping), or, put a piece of masking tape on the back part of the cup that touches the rubber rollers on the Rotary Device.
- Use rubber bands on the cup where it touches the rollers to improve grip on the mug to prevent slipping.
- If you make a mistake on an expensive mug, it is suggested that Scotch Bright and some other lacquer thinner will take off the CerMark, just make sure you only scrub with the grain of the stainless.
I didn’t know you could engrave steel mugs with lasers. It would be really fun to have one of those machines because you could basically make sure any engraving gets put on your mugs. Think about the business you could get by engraving mugs.
You make engraving sound so much easier than I thought. I can’t wait to see how my mug turns out.
When engraving tapered mugs, stainless or powder coated, the logo design is distorted.
Is there a way to compensate for the taper or just avoid those type of mugs altogether. I’ve found that most forums are little help. Too many “experts”
Thanks in advance,
Jerry A. Platter
Star Graphics
Hi Jerry,
It depends on the laser machine you are using. I assume you are using a rotary device of some sort. When we engrave tapered objects we adjust the object so that it is level with the laser beam. You could also try altering the artwork you are lasering with your design software. Corel has an envelope tool that I’ve heard works well for this.
hi I have a corel software along with an epilog mini laser and my question is we are gonna engrave on a black coated cup and our machine only does black and gray will it show up if we keep the image black on our software or is there a specific way to do it?
Hi Victoria,
I am not an authority of Epilog lasers, but they are similar to AP Lazer when it comes to engraving. Yes,anything that is black in your file will remove the coating on the mug. When you see a black engraving on a stainless mug, that is because a metal marking solution was used. (We use Cermark.) Hope this helps!
You make a good point about how steel tumblers are nigh unto indestructible. I imagine it would be sweet to have one laser engraved like this so you could show it off at events!
A good blog! I will bookmark a few of these..